|
|
|
|
|
|
|
|
|
|
|
|
|
- Nut For Engine Mount Bolt, Each
- (Ref. P/N: 98-9825-B)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- (Ref. P/N: N144438)
- This stud has a non-threaded area in the middle.
- These studs are used in a variety of locations
including intake studs, exhaust studs, oil pumps, fuel
pumps, etc.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- 6mm/8mm x 23mm Step Stud, Each
- (Ref. P/N: N144521)
- Used on the oil drain sump plate when the stock thread is stripped out.
- Requires tapping of case to 8mm.
- The 8mm end of stud goes into the case and the 6mm end sticks out.
|
- Starter Bolt, Each
- (Ref. P/N: 98-1003-B)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Metal Cam Plug
- For case with groove
- Fits 1300-1600cc
|
- Engine Mount Bolt, 10 x 70mm, Each
- (Ref. P/N:98-9824-B)
|
- Universal fit
- Keeps the oil in and the dirt out
- Install on Type 1 case with stock or aftermarket dipstick
- Sold individually
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Rubber Cam Plug
- For O.E. case without groove
|
- M10-1.5 x 85mm Double End Stud, Each
- (Ref. P/N: N145251)
- This stud has a non-threaded area in the middle.
- Fits all engines except where 091 transmission is used.
- Two studs are needed to mount case to the transaxle.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Includes thick metal block-off plate and gasket
|
- Block off with 12mm threaded breather boss
- Includes mounting gasket
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Block-Off Plate has a 1/8" NPT tapped hole
- Includes gasket
|
Shroud Screw Kit 12 pieces
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Engine Mounting Bolt 5 Piece Set
- Late case using Dog House Type Cooler (71-on)
|
- Brass
- Thread: 8mm-1.25
- Head: 11mm
- Set of 8
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Quick repair for stripped head studs
- 10mm x 240mm studs
- Fits 1500-1600cc
- Sold per stud
|
- Bright zinc nylock nuts resist vibration, maintain torque and prevent oil seepage
|
- Steel Plated Exhaust Nuts
- Thread: 8mm-1.25
- Head: 11mm
- Set of 8
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- 6 Point 8mm Engine Nuts, Gold Zinc Plated, 8 pcs
- 8mm-1.25 Thread, uses 10mm Wrench Size
|
- Adds dipstick tube to Type 3 and universal cases
|
|
|
|
